Orangutan SVP-1284 Robot Controller assembled
The Orangutan SVP robot controller is a complete control solution for small and medium-sized robots running at 6 – 13.5V.
The module is designed around the powerful Atmel ATmega324PA AVR
microcontroller (32KB flash, 2KB RAM, and 1KB EEPROM) or ATmega1284P (128KB flash, 16KB RAM, and 4KB EEPROM)
running at 20MHz and features a full complement of peripheral hardware to support robotics applications:
dual motor drivers capable of delivering 2A continuous
(6peak) per channel, a demultiplexer for easy control of up to eight servos with a single hardware PWM,
a removable 16×2 character LCD with backlight, a user trimmer potentiometer, a buzzer for simple sounds and music,
three user pushbuttons, and two user LEDs. The board also provides 21 free I/O lines,
of which 12 can be used as analog inputs, and two switching buck (step-down)
voltage regulators—one for the 5V bus and one adjustable from 2.5V to 85% of VIN—each capable of supplying 3A,
which means there’s plenty of room and power for adding sensors, servos, and other peripherals.
In addition to the user-programmable ATmega324 or ATmega1284 microcontroller, the Orangutan
SVP features an auxiliary PIC18F14K50 MCU that supports the main processor and serves as an integrated AVR ISP programmer,
which means that no external programmer is required to use the Orangutan SVP.
This auxiliary processor provides a USB connection that allows direct communication with a PC,
and its firmware lets it perform several useful tasks in parallel with the main microcontroller.
For example, the auxiliary processor can read two quadrature encoders, such as encoders for
Pololu wheel 42×19mm or our 37Dmm metal gearmotors with encoders, without burdening the main MCU,
or those same four inputs could be used as additional analog inputs.
The user AVR can read data from the auxiliary MCU over SPI. A USB A to mini-B cable is included with the Orangutan SVP.
The Orangutan SVP is compatible with freely available development software
for Atmel’s AVR microcontrollers, including Atmel Studio and the WinAVR GCC C/C++ compiler.
We provide an extensive set of software libraries that make
it easy to interface with all of the integrated hardware, including the auxiliary microcontroller.
Using these libraries, it takes just a few simple lines of code to write to the LCD, read button presses,
drive motors, and control servos. These libraries come with a number of
sample programs that demonstrate how to use the various components on the Orangutan SVP.
מאפיינים
- Overall unit dimensions: 3.70" × 2.20"
- Input voltage: 6 – 13.5V
- Programmable 20MHz Atmel ATmega324PA AVR microcontroller with 32KB flash, 2KB SRAM, and 1KB EEPROM (SVP-324 version)
- Programmable 20MHz Atmel ATmega1284P AVR microcontroller with 128KB flash, 16KB RAM, and 4KB EEPROM (SVP-1284 version)
- Built-in USB AVR ISP programmer (USB A to mini-B cable included)
- 2 bidirectional motor ports (2A continuous per channel, 6A maximum per channel)
- 8-output demultiplexer tied to one of the user AVR’s hardware PWMs for easy control of up to 8 servos
-
21 free I/O lines
- 17 free I/O lines on the main AVR MCU, of which 8 can be analog inputs
- 4 input lines on the auxiliary processor, which can be either 4 analog inputs or dual quadrature encoder inputs
- 2 hardware UARTs
- Removable 16-character × 2-line LCD with backlight
- Primary 5V switching regulator capable of supplying 3A
- Secondary adjustable (2.5V – 85% of VIN) buck (step-down) voltage regulator capable of supplying 3A
- Buzzer tied to one of the user AVR’s hardware PWMs
- 3 user pushbutton switches
- 2 user LEDs
- Power (push-on/push-off) and reset pushbutton switches
- Power circuit makes it easy to add extra power buttons and provides a self-shutdown option
-
Auxiliary processor (connected via SPI) provides:
- Battery voltage reading
- User trimmer potentiometer reading
- Integrated USB connection
- In-System-Programming of the main processor
- Ability to read two quadrature encoders
-
Comprehensive user’s guide
מידות
| Size: | 3.70" x 2.20" |
|---|---|
| Weight: | 2.7 oz |
מאפיינים כלליים
| Processor: | ATmega1284P @ 20 MHz with auxiliary PIC |
|---|---|
| RAM size: | 16384 bytes |
| Program memory size: | 128 Kbytes |
| Motor driver: | Dual TB6612FNGs |
| Motor channels: | 2 |
| User I/O lines: | 211 |
| Max current on a single I/O: | 40 mA |
| Minimum operating voltage: | 6 V |
| Maximum operating voltage: | 13.5 V |
| Continuous output current per channel: | 2 A |
| Peak output current per channel: | 6 A |
| Current sense: | 0.85 V/A |
| Maximum PWM frequency: | 80 kHz |
| Reverse voltage protection?: | Y |
| External programmer required?: | N |
| LCD included?: | Y |